Rasid hardware units

GPS Device specification requirements for Implementation of  RASID System

Requirements (Minimum Mandatory)

SIM card requirements

Provide GPRS/3G data sim card with a minimum data capacity of 20 Mb for a month.

GSM(GPRS)

Quad Band 900/1800 MHz, 850/1900 MHz

GPRS Class 10 (Upto 85.6)

SMS for OTA configuration

GPS/GPS+GLONASS

NMEA-0183 Protocol

32 channel receiver

High sensitivity, not less than -161 dBm

IMEI

Device IMEI should be valid under TRA

Latitude & Longitude Format

Device should send the latitude and longitude in decimal format

Date & Time Format

Device should sent the date and time in UTC format

Speed Format

Device should send the speed in miles/hour format

Direction Format

Device direction setting should have 0-360 degrees

Digital Inputs

Minimum 2 digital inputs

Digital Outputs

Minimum 2 digital outputs

Analog Inputs

Minimum 1 analog input

1 Wire Interface

Device Should have 1 wire interface for temperature/ibutton

Power supply

The power supply should be between +5 to +30 v

USB/Serial interface

The USB/Serial interface should be available for initial configuration

Internal battery

The internal battery should have a minimum backup of 24 hours

FOTA/ USB/ Serial

The firmware of the device should be upgradable through OTA as well as USB/Serial interface

Flash Memory

Flash memory should be minimum 2 MB ( or equivalent to >= 2000 offline records) for saving the records, when GSM not available

Data-sending mode

Device should send the data in time, distance and direction mode

PTO Connection 

To get the PTO status

CAN Interface

Mandatory for the vehicles that have CANBUS for accurate data

On-Board Weighing System for Bulk Collection

Communication 

RS232 Communication (Serial Communication) 

Weight data

Total weight

Weight per location 

Partial weight (weight on collection)

Alerts Configuration

Configuring weight limit

Alert for overloading

Data pushing mode

Data pushing on event (bin collection)

Data pushing on predefined Interval

Data polling mode

Data Polling on Request(online Polling) 

Weight Sensors

To get the weight of the bins based on location

Accuracy

1% full scale

Capacity (GVW)

17 -50 Tons

Operating Voltage

15 -30V  

Operating temperature

0 to 60 degree C

Inclinometer –
chassis lean alarm

3 degrees

Inclinometer –
body load alarm

40% off centre

Weighing modes

Standard, axle, twin/5th wheel and air, drawbar

Indicator type

LCD

Indicator size

79.0 x 30.9 mm

Indicator operating temperature

-10 to + 50 °C

Indicator environmental protection

IP20

Indicator resolution 240 x 90 Dots

240 X 90 dots

Dot pitch

0.42 mm

Load cell port

4 pin connector (for junction box)

Overload alarm - audible

Optional external alarm sounder on vehicle

Password protection

4 digits, manager and user PIN

Form factor

Din cut out

Load cell types

Up to 8 CANbus or analogue load cells

Interfaces

RS232

Baud rate

1200, 2400, 9600, 19200, 57600

Connector 

9 pin to printers/scoreboard bps

Printer capability

Impact or heavy duty type

Wireless
Remote
Handheld Unit

Range Up to 50 meters in open terrain
15 channels , A-O, Frequency 868MHz (complies with the European license free ISM band regulations)
Viewing area 50.6 x 31.0 mm
Minimum voltage 3.3 (with reminder on screen) Vdc
Max charging voltage 4.2 V dc
Charging time Three hours approximately, discharged to full, Battery type -Nickel Metal Hydride, rechargeable – ruggedized, Backlight 8 seconds per button push, IP 66 Protection

RFID Interface

For the personnel identification

Two-way communication

With the driver

Features and alerts within the device

Ignition On/Off

Ignition On/Off status alert

Engine Immobilization

Engine Immobilization (as output)

Overspeed

Overspeed alerts

SOS button (optional)

SOS alert during emergency – Panic Button

Harsh braking

Harsh braking alert during rash reduction in velocity

Harsh cornering

Harsh cornering alert during rash change in angular velocity

Harsh Acceleration

Harsh acceleration alert during rash change in velocity

Temperature Sensor (optional)

Environment temperature

Fuel Sensor (optional)

Fuel sensor for the detection of fuel level of the device

Device battery Low

Battery Low status of internal and external battery

Towing

Tow alert during illegal movement of the vehicle

Tampering/Battery Removed

Tampering/Battery Removed alert when primary power supply is cut off

Geo-fence

Geo-fence feature should be available within the device

Weight

The weight of the collected waste based on the location

The container level sensor should be designed and built to accurately measure container fill levels in harsh environmental conditions. It should employ ultrasonic sonar technology together with temperature and motion sensors. The smart software should be able to measure the fill level and automatically detect important events such as container collections, fire and vandalism. Advanced algorithms to be applied to determine the fill level even if the surface of the contents is unevenly shaped. Measurements to be performed at confgurable intervals, usually once per hour.

  • Reader
    • Reads any Maxim iButton through 1-wire (onewire) interface
    • All metall parts are chromium-plated
    • Should be compatible with any access control device
    • Plastic casing
    • M12 thread
    • Standard wire - 40 cm
    • Waterproof
  • ID
    • Waterproof iButton probe without LED
    • Reads any Maxim iButton through 1-wire (OneWire) interface
    • Should be compatible with any access control device
    • Standard wire - 40 cm
    • Made from high grade stainless steel: 1.4418
    • Full resistance to halogen elements (e.g. sea water)
    • Should be compatible with UTAH-P (magnetic) holders

 

Useful links

  • Visit Dubai
  • Dubai
  • Dubai Expo 2020
  • Government of Dubai
  • UAE Government
  • Dubai Airport
  • Dubai Smart Government